Mid-Illini Jeepers

If you hot wire the pump will it start and run?

I don't remember which year you have, but the distributor signal is used to fire the injectors, and the flywheel sensor is used to fire the plugs.

https://www.full30.com/video/0ed306899e ... 5971c92554

https://www.full30.com/video/ece7d1ddb3 ... f2e0a84394

FYI - http://www.asymmetricsolutionsusa.com/

Not that I follow it, but here is my list of Suggested Off-Road Gear:

http://wawii.com/m37/Suggested_Off-Road_Gear.pdf

WOW, you sure are hitting some unique snags.

Well, a couple of you know, but now the rest of you will. I'm now the proud (well OK maybe not proud) and somewhat intrigued by, owner of a 1982 Jeep Wagoner Limited. I've drained the bad fuel from the fairly clean plastic tank and ordered a new pickup/fuel float, running it from a gas can for now. ...

First, Happy Thanksgiving! Well, last night at 9:30 I was unloading the trailer and on the road off on a Durango retrieval run. After the kids left the house for Thanksgiving Dinner about 5-10 miles from the house the Durango blew coolant out the radiator cap, and then the temp gauge went high. So i...

Well gang, Darrell just got back from Iowa (helping is daughter make the move to Carroll IA), and with the farm and weather he's not going to be able to make the trip. At this point I'm on the fence, as the M's not up to a Flat Nasty with out the rear locker, and the Jeep needs a little more ground ...

I wonder if you are getting this error and your browser is kicking you out?

The attachment’s file size is too large, the maximum upload size is 2 MB.
Please note this is set in php.ini and cannot be overridden.


I've attached two pictures to this to test
.

I've considered (had better have before rock crawling again) building a skid plate to protect the underside of my YJ's engine oil pan and transmission pan. However before I go looking for steel and doing some planning and fabricating, I'm considering it might just be wiser to buy one. My YJ is the 4...

I should make it, and may have a passenger.

Yep, just as Tom did.

Great to see!

Welcome to the area, Could the Sequel be a whistle? On a 04 Dakota I just picked up the muffler is in need of replacing and it whistles.

As always another great time with Food and Friends!

I got 14.3 MPG in the YJ for the 167'ish mile round trip.

Thanks to everyone!

Thanks for the confirmations! Now to jumper or connect the leads together that Painless had in the harness for the NSS. The only other modification to the harness so for has been to route the reverse leads thru the bulk head connector so they can be connected tot he stock Trans/Transfer harness at t...

Well, it looks like Bill to the Rescue again? I found a post from him in November 2011 on the Jeep Forum that seems to indicate there is NO Neutral Safety Switch.

Neutral safty and 4wd indicator wiring: http://www.jeepforum.com/forum/f8/neutr ... st12566214

OK gang, the 1983 CJ7 I'm working on has a manual 4 speed with a manual clutch (stock) and the 4.2L in-line 6 (stock). I'm re-wiring it and I didn't find a neutral safety switch on the trans, just a back-up circuit, and a 4WD indicator circuit. The clutch pedal doesn't have a switch on it either. Al...

Bill, with no Rims/Tires and the salvage Title and dis assembly, the 3-4K sounds about right from what I've seen, but always try to get it on the cheep.

The TorqueFlite 999 (32RH) is a 904 (30RH) based Transmission and is NOT the same case/pan as the 727 series of transmissions. Heavy Duty TorqueFlite Transmssions A727 (36RH/37RH) A518 (46RH/46RE) A618 (47RH/47RE/48RE) Light Duty TorqueFlite Transmssions A904 (30RH) A998 (31RH) A999 (32RH) A500 (40R...

Worked for me. It's a lime green Jeep with both full and half doors and a black hardtop.

https://youtu.be/WA3ravewH6o

Especially if more than 1", but even at 1" on a YJ the shift linkage (on an automatic) must be adjusted and the radiator/fan shroud lowered. The 1" kit I installed on the TJ was pretty good, it came with the 1" adapter to address the 4x4 shifter, but it only wanted the fan shroud...

I've got a 1" Body Lift on my YJ, and as long as the body bolts come out with ease it's an easy install. Adds some additional tire clearance with out raising COG. Next is to add a little suspension lift.

On my ARB's there is a metal rotation limiter that is bolted ont op of the bearing cap (right side of photo).