CJ3B #2
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
CJ3B #2
On with the Cj3B build, but with smaller pictures that you can actually load
Body prep is next, bottom had been rebuilt at some point and is not in bad shape, a little rattle can paint and we are good
Jeep was originally green, so I'm staying with that
Body prep is next, bottom had been rebuilt at some point and is not in bad shape, a little rattle can paint and we are good
Jeep was originally green, so I'm staying with that
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
Drivers side body work
Lots of bubba bondo, pop rivets, rust and holes
bondo removed, holes, rust cut clean
new steel welded in
Bardo bondo added, 1st pass priming- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
Levitated body
rolled in chassis
lowered body onto chassis
old bondo removed, rust cut out
-
- Posts: 2609
- Joined: Thu Jan 27, 2005 10:14 am
- MIJC Member: Yes
- Full Name: Tom and Sally Evans
- Member page: http://mijc.org/members/e-j/tom-sally-evans/
Re: CJ3B #2
Wow Dan you do good work.
It's hip to be square!!! []lllll[] NVRDUN9 93 YJ SOA XJ spring stretch, High pinion 9" rear Detroit locker, Dana 44 front ARB locker, 4.56 gears, Sanden OBA, Warn M8274 winch, 36" Iroks, Turtle enterprises swing out tire carrier
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
Thanks
Its my Therapy
Its my Therapy
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
So, On with the 3B build, I have been working through the winter, just seems like not enough to post
The Body is patched, primed, 1st coat of paint and now mounted
hanging pedals have been modified and ready for last fitting
will be put in after steering is in
The Body is patched, primed, 1st coat of paint and now mounted
hanging pedals have been modified and ready for last fitting
will be put in after steering is in
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
Firewall reinforced inside and out for hanging pedals
steering hole moved up about 1+ inch so steering shaft would miss motor mount
steering hole moved up about 1+ inch so steering shaft would miss motor mount
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
So. on with the 3B build
hanging pedals hooked up to clutch and brakes
clutch cable is a Blazer rear E-brake cable gas tank installed and seat frames built Oh and in case you wondered
the yard Jeep is planted
hanging pedals hooked up to clutch and brakes
clutch cable is a Blazer rear E-brake cable gas tank installed and seat frames built Oh and in case you wondered
the yard Jeep is planted
- Jon Martin
- MIJC Events Coordinator
- Posts: 765
- Joined: Wed Jan 26, 2005 4:42 pm
- MIJC Member: Yes
- Full Name: Jon Martin
- Member page: http://mijc.org/members/k-o/martin-jon/
- Location: Pekin, Illinois
Re: CJ3B #2
So that's two jeeps in the landscaping now.
MIJC member since 1998!!!
President of Turtle Enterprises and DBA
1951 CJ3A
President of Turtle Enterprises and DBA
1951 CJ3A
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
still moving along on the CJ3B
gas tank in
seats in
Gas pedal in (CJ 7) (still have to hook up)
Tailgate on (chain being painted)
gas tank in
seats in
Gas pedal in (CJ 7) (still have to hook up)
Tailgate on (chain being painted)
- DanB
- Posts: 174
- Joined: Thu Jan 18, 2007 2:06 pm
- MIJC Member: Yes
- Full Name: Dan Barding
- Member page: http://mijc.org/members/a-d/dan-betty-barding/
- Location: Central IL
Re: CJ3B #2
Update, CJ3B is running and moving
took it down the drive, but not far
still no brakes, maybe its the proportioning valve
might try it with none
took it down the drive, but not far
still no brakes, maybe its the proportioning valve
might try it with none
- Attachments
-
- DSC05984 (640x480).jpg (236.11 KiB) Viewed 36312 times
- Jon Martin
- MIJC Events Coordinator
- Posts: 765
- Joined: Wed Jan 26, 2005 4:42 pm
- MIJC Member: Yes
- Full Name: Jon Martin
- Member page: http://mijc.org/members/k-o/martin-jon/
- Location: Pekin, Illinois
Re: CJ3B #2
Looking good!
MIJC member since 1998!!!
President of Turtle Enterprises and DBA
1951 CJ3A
President of Turtle Enterprises and DBA
1951 CJ3A