Moab 2017

Check here for updates on MIJC Events.
TSEJEEPERS
Posts: 2457
Joined: Thu Jan 27, 2005 10:14 am
MIJC Member: Yes
Full Name: Tom and Sally Evans
Member page: http://mijc.org/members/e-j/tom-sally-evans/

Re: Moab 2017

Post by TSEJEEPERS » Wed Jun 07, 2017 2:29 pm

tchpet wrote:Tom, leaving Peoria at 8:15am. Does it make sense to meet at Shell in Kickapoo? Probably around 8:30?

Shannon
Sounds good, see you there.
It's hip to be square!!! []lllll[] NVRDUN9 93 YJ SOA XJ spring stretch, High pinion 9" rear Detroit locker, Dana 44 front ARB locker, 4.56 gears, Sanden OBA, Warn M8274 winch, 36" Iroks, Turtle enterprises swing out tire carrier

User avatar
tchpet
Posts: 105
Joined: Thu Aug 16, 2012 5:04 pm
MIJC Member: Yes
Full Name: Shannon Duling
Member page: http://mijc.org/members/a-d/duling-shannon/

Re: Moab 2017

Post by tchpet » Sat Jun 17, 2017 7:55 pm

Great time! Thanks to everyone, especially Larry for making arrangements. Now, does anyone know anywhere that welds aluminum? On the way home, blew a tire on the trailer and tore up step and fender....ugh! Those damn potholes through Colorado were bad!

vlucdog
Posts: 1051
Joined: Wed May 24, 2006 7:31 pm
MIJC Member: Yes
Full Name: Bill Gangloff
Member page: http://mijc.org/members/e-j/bill-vicki-gangloff/
Location: peoria,il.

Re: Moab 2017

Post by vlucdog » Sat Jun 17, 2017 9:43 pm

You could call Hamm's, the guys who make the plate boats.
83- cj7, 80-cj5, 77 cj5 for parts

JG&TG
Posts: 38
Joined: Tue Jul 26, 2011 5:23 pm
MIJC Member: Yes
Full Name: John Geiselman
Member page: http://mijc.org/members/e-j/geiselman-john-toni/
Location: El Paso

Re: Moab 2017

Post by JG&TG » Sun Jun 18, 2017 10:37 pm

tchpet wrote:
Sat Jun 17, 2017 7:55 pm
Great time! Thanks to everyone, especially Larry for making arrangements. Now, does anyone know anywhere that welds aluminum? On the way home, blew a tire on the trailer and tore up step and fender....ugh! Those damn potholes through Colorado were bad!
You need some training wheels for that trailer?
2005 TJ

TSEJEEPERS
Posts: 2457
Joined: Thu Jan 27, 2005 10:14 am
MIJC Member: Yes
Full Name: Tom and Sally Evans
Member page: http://mijc.org/members/e-j/tom-sally-evans/

Re: Moab 2017

Post by TSEJEEPERS » Mon Jun 19, 2017 8:36 am

I had a great time too!
Thanks to Larry for the lodging and Jane and Pam for doing the cooking.
Now on to the good stuff.
Damage report:
If I miss some thing feel free to add.
Scott Dammerman: Brake line, Clutch issues, rear drive shaft (3), and a starter.
Steve Vohs: rear drive shaft, rear hub seal, clutch.
Fraser Yarker: rear axle bearing and seal.
Tom Evans: air line for OBA.
Al Wallace: Rear upper control arm mount.
John Geiselman: Laid the Jeep on it's side. (Body damage)
It's hip to be square!!! []lllll[] NVRDUN9 93 YJ SOA XJ spring stretch, High pinion 9" rear Detroit locker, Dana 44 front ARB locker, 4.56 gears, Sanden OBA, Warn M8274 winch, 36" Iroks, Turtle enterprises swing out tire carrier

Fraser
Posts: 899
Joined: Wed Jan 26, 2005 12:14 pm
MIJC Member: Yes
Full Name: Fraser Yarker
Member page: http://mijc.org/members/u-z/yarker-fraser/
Location: Pekin, IL
Contact:

Re: Moab 2017

Post by Fraser » Mon Jun 19, 2017 12:11 pm

tchpet wrote:
Sat Jun 17, 2017 7:55 pm
Now, does anyone know anywhere that welds aluminum?
Pekin Weldors Inc on Edgewater Drive welds aluminum, or used to.
1998 TJ (Wrangler) - usually driveable
19xx J-truck
Parts

User avatar
Duke Winch
Posts: 1004
Joined: Wed Jan 26, 2005 6:55 pm
MIJC Member: Yes
Full Name: Steve Vohs
Member page: http://www.mijc.org/members/u-z/vohs-steve/
Location: Ramsey, IL

Re: Moab 2017

Post by Duke Winch » Mon Jun 19, 2017 2:33 pm

TSEJEEPERS wrote:
Mon Jun 19, 2017 8:36 am
I had a great time too!
Thanks to Larry for the lodging and Jane and Pam for doing the cooking.
Now on to the good stuff.
Damage report:
If I miss some thing feel free to add.
Scott Dammerman: Brake line, Clutch issues, rear drive shaft (3), and a starter.
Steve Vohs: rear drive shaft, rear hub seal, clutch.
Fraser Yarker: rear axle bearing and seal.
Tom Evans: air line for OBA.
Al Wallace: Rear upper control arm mount.
John Geiselman: Laid the Jeep on it's side. (Body damage)
Could not have said it better. Beautiful part of the country.

Steve
2000 TJ, D60s, 38" TSLs, 4:1 Transfer Case, 4 link rear, 3 link front, 9" stretch, hydro steering
Duke's Off Road...Where if you don't have an engineering problem, We'll design one for you!
Duke's Off Road Ranch - Closed for winter

Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests