Page 1 of 1
CJ3B #2
Posted: Sat Nov 01, 2014 7:48 pm
by DanB
On with the Cj3B build, but with smaller pictures that you can actually load
Body prep is next, bottom had been rebuilt at some point and is not in bad shape, a little rattle can paint and we are good
Jeep was originally green, so I'm staying with that
- DSC05934 (640x480).jpg (216.43 KiB) Viewed 37205 times
Re: CJ3B #2
Posted: Mon Nov 10, 2014 8:10 pm
by DanB
Drivers side body work
- Drivers side.jpg (18.64 KiB) Viewed 37172 times
Lots of bubba bondo, pop rivets, rust and holes
- DSC05935 (640x480).jpg (223.46 KiB) Viewed 37172 times
bondo removed, holes, rust cut clean
- DSC05939 (640x480).jpg (213.47 KiB) Viewed 37172 times
new steel welded in
- DSC05943 (640x480).jpg (220.63 KiB) Viewed 37172 times
Bardo bondo added, 1st pass priming
Re: CJ3B #2
Posted: Sat Nov 29, 2014 9:22 pm
by DanB
Levitated body
- DSC05945 (640x480).jpg (202.03 KiB) Viewed 37131 times
rolled in chassis
- DSC05946 (640x480).jpg (206.04 KiB) Viewed 37131 times
lowered body onto chassis
- DSC05947 (640x480).jpg (203.91 KiB) Viewed 37131 times
old bondo removed, rust cut out
- DSC05949 (640x480).jpg (195.3 KiB) Viewed 37131 times
Re: CJ3B #2
Posted: Sun Nov 30, 2014 8:29 am
by TSEJEEPERS
Wow Dan you do good work.
Re: CJ3B #2
Posted: Sun Nov 30, 2014 10:54 am
by DanB
Thanks
Its my Therapy
Re: CJ3B #2
Posted: Mon Mar 09, 2015 7:34 pm
by DanB
So, On with the 3B build, I have been working through the winter, just seems like not enough to post
The Body is patched, primed, 1st coat of paint and now mounted
hanging pedals have been modified and ready for last fitting
will be put in after steering is in
- DSC05951 (640x480).jpg (201.57 KiB) Viewed 36867 times
- DSC05958 (640x480).jpg (193.31 KiB) Viewed 36867 times
- DSC05960 (640x480).jpg (196.72 KiB) Viewed 36867 times
- DSC05961 (640x480).jpg (195.11 KiB) Viewed 36867 times
- DSC05956 (640x480).jpg (203.56 KiB) Viewed 36867 times
Re: CJ3B #2
Posted: Wed Mar 11, 2015 6:48 pm
by DanB
Re: CJ3B #2
Posted: Sat Jul 25, 2015 8:15 pm
by DanB
So. on with the 3B build
hanging pedals hooked up to clutch and brakes
clutch cable is a Blazer rear E-brake cable
- DSC05964 (640x480).jpg (192.17 KiB) Viewed 36618 times
- DSC05965 (640x480) (2).jpg (206.94 KiB) Viewed 36618 times
gas tank installed and seat frames built
- DSC05966 (640x480).jpg (211.92 KiB) Viewed 36618 times
Oh and in case you wondered
the yard Jeep is planted
- DSC05967 (480x640).jpg (262.54 KiB) Viewed 36618 times
- DSC05968 (640x480).jpg (292.85 KiB) Viewed 36618 times
Re: CJ3B #2
Posted: Wed Aug 26, 2015 9:19 pm
by Jon Martin
So that's two jeeps in the landscaping now.
Re: CJ3B #2
Posted: Wed Sep 02, 2015 7:59 pm
by DanB
still moving along on the CJ3B
gas tank in
seats in
Gas pedal in (CJ 7) (still have to hook up)
Tailgate on (chain being painted)
- DSC05970 (640x480).jpg (195.6 KiB) Viewed 36487 times
- DSC05969 (640x480).jpg (191.84 KiB) Viewed 36487 times
- DSC05974 (480x640).jpg (205.86 KiB) Viewed 36487 times
- DSC05975 (640x480).jpg (208.51 KiB) Viewed 36487 times
Re: CJ3B #2
Posted: Sun Nov 08, 2015 4:12 pm
by DanB
Update, CJ3B is running and moving
took it down the drive, but not far
still no brakes, maybe its the proportioning valve
might try it with none
- DSC05987 (640x480).jpg (262.02 KiB) Viewed 36291 times
- DSC05986 (640x480).jpg (256.32 KiB) Viewed 36291 times
- DSC05985 (640x480).jpg (248.34 KiB) Viewed 36291 times
Re: CJ3B #2
Posted: Sun Nov 08, 2015 5:32 pm
by Jon Martin
Looking good!